Experimental investigations of opening leaks in a welded seam of a closed container under thermal and acoustic influences

To conduct experimental investigations of the drying process of a closed container, taking into account the opening of a leak channel in a weld, an experimental research stand, an experimental container and experimental samples with model leaks of different sizes are designed and manufactured. The scientific problem of experimental research has been formulated, a program and methods for conducting experiments have been developed. Requirements for metrological equipment have been formed and the measurement error of temperature, humidity and pressure has been determined. Preliminary experiments are carried out on wetting the experimental container and experimental samples with a model liquid and clogging the leak channels, as well as on drying the inner surface of the experimental container wall with a convective gas flow and conductive heating of the wall until the leak channels clogged with liquid are opened. The dependences of the change in temperature of the liquid, air, wall of the experimental container, experimental samples and pressure in the experimental container are obtained over the time of the experiment during wetting and drying of the experimental container and experimental samples. The parameters of thermal exposure at which the leak channels is opened within a specified time are determined.

1. OST 92-0019-78. Metody i rezhimy sushki izdeliy pered ispytaniyami na germetichnost’ [Methods and modes of products drying prior to air-pressure test]. 80 p. (In Russ.).

2. Lin P., Basem A., Alizadeh A. [et al.]. Effect of temperature on the mechanical properties of aluminum polycrystal using molecular dynamics simulation // Case Studies in Thermal Engineering. 2024. Vol. 59. 104480. DOI: 10.1016/j.csite.2024.104480. (In Engl.).

3. Wu C., Li J. Numerical simulation of flow patterns and the effect on heat flux during R32 condensation in microtube // International Journal of Heat and Mass Transfer. 2018. Vol. 121. P. 265–274. DOI: 10.1016/j.ijheatmasstransfer.2017.12.123. (In Engl.).

4. Dinyayeva N. S., Kravtsov S. B., Krumlyakov S. O. [et al.]. Stend zapravki teplovykh trubok [Stand for filling heat pipes] // Trudy MAI. Trudy MAI. 2022. No. 126. DOI: 10.34759/trd-2022-126-13. EDN: RRYFVC. (In Russ.).

5. Huang H., Zhai Y., Li Z. [et al.]. Thermo-hydraulic characteristics and structural optimization of supercritical CO2- cooled microchannel heat sink // International Communications in Heat and Mass Transfer. 2024. Vol. 154. 107438. DOI: 10.1016/j.icheatmasstransfer.2024.107438. (In Engl.).

6. Liu Y., Zeng L., Chen Y. [et al.]. Improving the cooling effect of proton exchange membrane fuel cells by using biomimetic capillary cooling channels based on topology optimization method // Applied Thermal Engineering. 2024. Vol. 251. 123633. DOI: 10.1016/j.applthermaleng.2024.123633. (In Engl.).

7. Karpovich I. N. Modelirovaniye peremeshcheniya zhidkosti v kapillyarakh i soplakh pechatayushchikh ustroystv [Modeling the movement of a liquid in capillaries and nozzles of printers] // Inzhenerno-fizicheskiy zhurnal. Journal of Engineering Physics and Thermophysics. 2023. Vol. 96, no. 2. P. 322–327. EDN: UIFKRZ. (In Russ.).

8. Naghashnejad M., Shabgard H., Bergman T. L. A novel computational model of the dynamic response of the evaporating liquid-vapor interface in a capillary channel // International Journal of Heat and Mass Transfer. 2022. Vol. 186. 122496. DOI: 10.1016/j.ijheatmasstransfer.2021.122496. (In Engl.).

9. Cai L., Lu Y., Zhang L. [et al.]. Leak tightness tests of mechanical seal joints for HL-2M tokamak under thermal cycle loads // Vacuum. 2023. Vol. 218. 112614. DOI: 10.1016/j.vacuum.2023.112614. (In Engl.).

10. Solov’yev V. N., Kologov A. V., Baryshnikov V. I. Istoricheskiye aspekty primeneniya edinits izmereniy v geliyevom techeiskanii [Historical aspects of the use of units of measurement in helium leak detection] // Vakuumnaya tekhnika i tekhnologiya. Vacuum Equipment and Technology. 2019. Vol. 29, no. 1. P. 23– 25. EDN: EWCDJW. (In Russ.).

11. Incropera F. P., DeWitt D. P., Bergman T. L. [et al.]. Fundamentals of heat and mass transfer. John Wiley & Sons, 2011. 1048 p. ISBN 1119722489; 978-1119722489. URL: https://mech.at.ua/HeatandMassTransfer7thEdition-Incropera-dewitt.pdf (accessed: 12.03.2024). (In Engl.).

12. GOST R 8.736-2011. Izmereniya pryamyye mnogokratnyye. Metody obrabotki rezul’tatov izmereniy. Osnovnyye polozheniya [State system for ensuring the uniformity of measurements. Multiple direct measurements. Methods of measurement results processing. Main principles]. Moscow, 2019. 21 p. (In Russ.).

13. GOST 24026-80. Issledovatel’skiye ispytaniya. Planirovaniye eksperimenta. Terminy i opredeleniya [Research tests. Experiment planning. Terms and definitions]. Moscow, 1991. 19 p. (In Russ.).

14. Boyko A. F., Kudenikov E. Yu. Tochnyy metod rascheta neobkhodimogo kolichestva povtornykh opytov [Exact methods calculate the necessary amount of repeat experience] // Vestnik Belgorodskogo gosudarstvennogo tekhnologicheskogo universiteta im. V. G. Shukhova. Bulletin of Belgorod State Technological University named after. V. G. Shukhov. 2016. No. 8. P. 128–132. EDN: WHTDML. (In Russ.).

15. Denisenko V. PID-regulyatory: voprosy realizatsii [PID controllers: implementation issues] // Sovremennyye tekhnologii avtomatizatsii. Modern Automation Technologies. 2008. No. 1. P. 86–99. URL: https://www.cta.ru/cms/f/364276.pdf (accessed: 12.03.2024). (In Russ.).

16. Spitsyn V. S., Spitsyn V. V. Algoritmy upravleniya temperaturoy v pomeshcheniyakh [Algorithms for temperature control in buildings] // Vestnik YuUrGU. Seriya «Komp’yuternyye tekhnologii, upravleniye, radioelektronika». Vestnik SUSU. Series «Computer Technology, Automatic Control, Radio Electronics». 2012. No. 35. P. 79–84. EDN: PEWAJJ. (In Russ.).